ارور ماشین های لباسشویی بهی

number

description

display

F1

connection to temperature sensor open or short-circuited

The failure is set, if the connection to the temperature sensor is open or if there is a short circuit between the two terminals of the sensor. The washing program will be ended without heating. The failure will be displayed at the end of the washing program. This must be check at beginning of program and again before heating step.

All LED repeatedly pulsate:

1 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F2

The connection with door lock is open

The failure is set, if the connection to the door lock is open. The washing program will be stop. The failure will be displayed. Supply of door lock will be ON. To start the washing program, the user has to close the door (at on start program). To continue the program (if failure happen between washing program), the user has to check if is the door close and press the „Start“-button. If the failure occurred again, the washing program is stopped. Supply of door lock will be OFF. If is water in the machine, than pumping 2 minutes. Failure will be displayed again , and it is not possible to start the washing program again.

All LED repeatedly pulsate:

2 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F3

the water level was not reached.

– water tap closed

– leak in the machine

– valve defect

The failure is set, if within an filling or heating step the water level is below level 1 for the filling time or 4 minutes in heating time. If the failure occurred the first time within a washing program, the current step will be started again. If the failure occurred the second time (twice in succession), the washing program is stopped, and the failure will be displayed. To continue the washing program, the user has to press the „Start“-button. If the failure occurred the third time, the washing program is stopped, the failure will be displayed, and it is not possible to start the washing program again.

All LED repeatedly pulsate:

3 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F4

the connection to the tacho generator is open or short-circuited

If the washing program is active and the motor control unit gets no signal from the tacho generator, the first time the failure occurs a pause of 1minute is executed. This repeat 3 times. If once happen that motor work O.K. than all previous failure must be deleted. When the failure is detected the 4 time’s the washing program is stopped immediately. If is temperature higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. STOP the program. The failure will be displayed.

All LED repeatedly pulsate:

4 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F5

the triac is short-circuited

The failure is set, if the washing program is active and the motor is working without control of triac. The washing program is stopped immediately. After 2 minutes try again. If the failure is not present, than forget the first failure and continue work. If is the same failure again, than program stop complete. If is temperature higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. STOP the program. The failure will be displayed.

All LED repeatedly pulsate:

5 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F6

temperature not reached

– heater defect

The failure is set, if after a heating step the temperature is more than 15°C lower than the rated temperature. The washing program will be ended normally. The failure will be displayed at the end of the washing program.

All LED repeatedly pulsate:

6 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F7

the water level does not fall below level 1

– pump clogged

– pump defect

The failure is set, if after a pumping step the water level did not fall below level 1. If the failure occurred the first time within a washing program, the current step will started again. If the failure occurred the second time  (twice in succession), the washing program is stopped and the failure is displayed. To continue the washing program, the user has to press the „Start“-button. If the failure occurred the third time, the washing program is stopped and the failure is displayed. It is not possible to start the washing program again.

All LED repeatedly pulsate:

7 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F8

The WM not reach max. spin speed (the tapped field relay does not switch)

The failure is set, if at the end of the spinning cycle of the testing program  the spin is more than 100rpm lower than the rated speed. The failure is displayed after the end of the testing program.

All LED repeatedly pulsate:

8 x ( ¼ sec. ON , ¼ sec. OFF)

than 5 sec. OFF(pause)

F1

connection to temperature sensor open or short-circuited

The failure is set, if the connection to the temperature sensor is open or if there is a short circuit between the two terminals of the sensor. The washing program will be ended without heating. The failure will be displayed at the end of the washing program.

On LCD: ERROR 1

F2

The connection with door lock is open

The failure is set, if the connection to the door lock is open. The washing program will be stop. Supply of door lock will be OFF. The failure will be displayed. To continue the washing program, the user has to close the door and press the „Start“-button. Repeat procedure like at START. If the failure occurred again, the washing program is stopped. . If is water in the machine, than pumping 2 minutes. Failure will be displayed again , and it is not possible to start the washing program again.

On LCD: ERROR 2

F3

the water level was not reached.

– water tap closed

– leak in the machine

– valve defect

The failure is set, if within an filling or heating step the water level is below level 1 for the filling time or 4 minutes in heating time. If the failure occurred the first time within a washing program, the current step will be started again. If the failure occurred the second time (twice in succession), the washing program is stopped, and the failure will be displayed. To continue the washing program, the user has to press the „Start“-button. If the failure occurred the third time, the washing program is stopped, the failure will be displayed, and it is not possible to start the washing program again.

On LCD: ERROR 3

F4

Inverter can’t control the motor

If the washing program is active and the motor control unit (Inverter) can’t control the motor, then first time the failure occurs a pause of 1 minutes. This repeat 3 times. If once happen that motor work O.K. than all previous failure must be deleted. When the failure is detected the 4 time’s the washing program is stopped immediately. If is temperature higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. STOP the program. The failure will be displayed.

On LCD: ERROR 4

FATAL Error

F5

No communication between electronic timer and Inverter

If the washing program is active and the motor control unit (Inverter) don’t have communication with main board, then first time the failure occurs a pause of 1 minutes. This repeat 3 times. If once happen that motor work O.K. than all previous failure must be deleted. When the failure is detected the 4 time’s the washing program is stopped immediately. If is temperature higher that 60°C than cool down with cold water 30 seconds. Then pumping water 2 minutes. STOP the program. The failure will be displayed.

On LCD: ERROR 5

FATAL Error

F6

temperature not reached

– heater defect

The failure is set, if after a heating step the temperature is more than 15°C lower than the rated temperature. The washing program will be ended normally. The failure will be displayed at the end of the washing program.

On LCD: ERROR 6

F7

the water level does not fall below level 1

– pump clogged

– pump defect

The failure is set, if after a pumping step the water level did not fall below level 1. If the failure occurred the first time within a washing program, the current step will started again. If the failure occurred the second time  (twice in succession), the washing program is stopped and the failure is displayed. To continue the washing program, the user has to press the „Start“-button. If the failure occurred the third time, the washing program is stopped and the failure is displayed. It is not possible to start the washing program again.

On LCD: ERROR 7

F8

The WM not reach max. spin speed (the tapped field relay does not switch)

The failure is set, if at the end of the spinning cycle of the testing program  the spin is more than 100rpm lower than the rated speed. The failure is displayed after the end of the testing program.

On LCD: ERROR 8

F9

Water inside machine

(Aqua Stop)

The failure is set, if Aqua Stop Sensor make signal (must be measuring min. 2 secundes).  The all valves switch OFF, the heater switch OFF and main motor STOP. After 3 secundes check again. If the failure is not present, than forget the first failure and continue with program. If the failure is still present, than switch ON the pump for 2 minutes and stop WM. The failure is displayed. It is not possible to start the washing program again.

On LCD: ERROR 9